emmett machinery logo
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors
       
  Account

Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Next day nationwide delivery

5 Star Service
50+ Years In Business
bulk buys available

need it quick?

Next day nationwide delivery *


5 Star Service
Check out our great reviews

50+ years
Highly experienced in the industry

free shipping

Free shipping on orders over £100*

Hand Press vs Industrial Eyelet Machine: Which Fits Your Workroom Volume?

There is a point in every curtain workroom where the hand press stops being a tool and starts being the bottleneck. Nobody plans for it. One month eyelet headings are a nice sideline, the next they’re a third of the order book and someone is spending Friday afternoon punching holes.

This guide works through where that point sits for an industrial eyelet machine, what the machine changes, and what to look at in the eisenkolb Hyproflex range we supply as sole UK agent. If you want the machines themselves, they’re all on our curtain eyelet machine page.

What a hand press asks of you

A hand press is a lever on a bench. You mark the ring centres along the heading, punch each hole (on most presses this is a separate die, so it’s a second pass), set the two halves of the eyelet in the die, pull the lever, move the curtain along, and repeat. Twenty rings on a wide panel is twenty of everything.

Three things cost you on a press like that.

01

Time

Every ring is a separate cycle, and the curtain has to be moved and squared up again between each one.

02

Consistency

The force comes from an arm and arms tire. Rings that don’t close cleanly have to be drilled out and replaced, taking a piece of eyelet buckram with them.

03

Heavy fabric

An interlined heading or a heavy velvet needs more pressure than most lever presses give, so the ring sits proud or the hole frays.

None of this matters at four pairs a month. It matters a great deal at four pairs a day.

The volume threshold

Here is the arithmetic we run with customers on the phone. Take a typical pair of eyelet curtains with 16 rings on each panel: 32 rings. The Hyproflex is rated at 100 to 150 rings an hour, so that pair is around 13 to 19 minutes of machine time, and the spacing comes from the machine’s ring distance setting, not a tape measure.

Here is how that scales with weekly output, at 32 rings a pair and 100 to 150 rings an hour:

Pairs a week Rings Hyproflex time
2 64 26 to 38 min
5 160 1h 04m to 1h 36m
10 320 2h 08m to 3h 12m
20 640 4h 16m to 6h 24m

Time your own hand press

Put one pair through your hand press with a stopwatch running, from first pencil mark to last ring, and multiply by your weekly pairs. When the hours on the press would pay a wage, the machine is the cheaper option, and that is before you count the rings you don’t have to redo.

What an industrial eyelet machine changes

An industrial eyelet machine does the hole and the ring in one cycle, under hydraulic pressure, with the fabric clamped. On the Hyproflex that looks like this:

One cycle

Two hydraulic cylinders punch the hole and press the ring at the same moment.

Clamped fabric

Hydraulic foot pedals hold the heading flat while you position it.

Set spacing

A handwheel sets the ring distance from 80mm to 230mm, the same for every ring, with no pencil marks on the fabric.

Same pressure

Hydraulic force is the same on the first ring and the five hundredth, so both halves close fully, even on heavy fabric.

A two-hand start keeps fingers clear of the dies. Our brass vs steel eyelets guide covers the metals; whichever you choose, a machine-set ring holds the stiffener evenly and the heading hangs straight.

The Hyproflex range

Three machines, all supplied, installed and serviced by us as sole UK agent for eisenkolb.

Hyproflex

The workhorse

  • Twin hydraulic cylinders and hydraulic foot pedals
  • Ring distance 80mm to 230mm by handwheel, head setting 10mm to 85mm
  • 40mm set as standard, quick-change tooling
  • Optional ring calculation module sets the distance for you
  • 100 to 150 rings an hour

View Hyproflex

Hyproflex E

Two ring sizes

  • Combined cutting and pressing in one cycle
  • Two pneumatic foot pedal fixation rods
  • 80mm to 230mm between tools, ruler 10mm to 85mm
  • Supplied with a 25mm or 40mm set
  • Quick-change knife and punch

View Hyproflex E

Second hand Hyproflex

Smaller budget

  • Same twin-cylinder hydraulic design
  • Hydraulic foot pedals and two-hand start
  • Quick-change tooling with a 40mm set
  • Price on request, availability varies

View second hand hyproflex

Hyproflex technical details

The figures below are for the standard Hyproflex. Ask us for the Hyproflex E brochure if you’re comparing the two.

Specification Hyproflex
Ring distance 80mm to 230mm
Head setting 10mm to 85mm
Standard tooling 40mm set, quick-change system for other sizes
Production capacity 100 to 150 rings an hour (depends on the operator)
Electrical 220V, single phase, 1100W
Air 6 bar, 0.1 litre per cycle
Footprint 110 x 75cm
Option Ring calculation module that works out and sets the ring distance

What to check on a second hand machine

If you’re buying used, from us or anywhere else, look at four things.

01

The dies

Worn punches leave a ragged hole that frays after washing. Ask when they were last replaced.

02

The hydraulics

A press that loses pressure mid-cycle leaves half-closed rings. Run a dozen rings on a heavy sample and check each one.

03

The tooling change

The quick-change system should swap sets without force or packing.

04

Your air supply

The Hyproflex needs 6 bar. A compressor that can’t hold it shows up as uneven rings on the busiest afternoon.

Matching tooling to fabric and eyelet size

The frame of the machine is not what decides which eyelets it can set; the tooling is. The Hyproflex comes with a 40mm set, which suits the 40mm rings we sell most of in both brass and steel and fits 25mm and 28mm poles. The Hyproflex E can come with 25mm tooling instead. For other sizes, ask us which tooling sets are available.

Fabric matters as much as size. Always press through buckram: the ring grips the stiffener, the stiffener spreads the load across the heading, and the curtain survives the washing machine. For very heavy interlined headings, tell us when you order and we’ll confirm the die set suits the thickness.

Which buckram width?

Our eyelet buckram vs pinch pleat buckram guide has a table of the buckram width to use with each eyelet size, from 25mm up to 66mm.

Install, training and after

Every eisenkolb machine we sell is delivered nationwide, installed and commissioned on site by our engineers, and your operators are trained on the day. Because we’re the sole UK agent, tooling, spares and service calls come from us in Stockport.

If you’ve already moved from a domestic to an industrial sewing machine, you’ll know the pattern. Our guide to that upgrade describes the same kind of jump.

Why there’s no price on the page, and what to ask instead

Every machine in our curtain eyelet machine range is priced on request because the configuration changes the number: which tooling sizes, whether you want the ring calculation module, and whether the machine is new or second hand. A figure that is wrong for your setup helps nobody, so we’d sooner have a five-minute call. Have these ready:

✓The eyelet sizes you sell

✓A typical week’s output in pairs

✓Your heaviest fabric

✓Whether you have compressed air on site

From that we can quote the machine, tooling and installation as one number, and arrange a demonstration.

Frequently asked questions

How many eyelets an hour does an industrial eyelet machine set?

The Hyproflex is rated at 100 to 150 rings an hour. The figure depends on the operator and the fabric, and includes positioning the curtain between rings.

Can a hand press set 40mm curtain eyelets in heavy fabric?

It can, with effort, and the results vary with the operator. Interlined and heavy fabrics are where a hand press struggles most, because the pressure comes from the lever. A hydraulic press gives the same force every time.

Does the Hyproflex need a compressor?

Yes. It needs 6 bar of compressed air and uses around 0.1 litres per cycle. Our engineer checks the supply at installation.

Is training included with an eisenkolb eyelet machine?

Yes. Installation, commissioning and operator training are part of every eisenkolb machine purchase from Emmett Machinery.

Talk to us before year end

If the press has become the bottleneck, call 0161 429 6929 or send your sizes and weekly volume through our contact page. We’ll tell you which Hyproflex fits, what it costs with tooling and installation, and when we can have it on your floor.

What makes us different?

Emmett Machinery Ltd are a long established company and provides specialist sewing and cutting equipment to the curtain and soft furnishings sector. We also supply an increasing range of consumable items. We are the sole agent for eisenkolb equipment in the UK, supplying to many large and small soft furnishing manufacturers alike.


Specialisation
Specialised supplier of sewing and cutting equipment, consumables, and machinery for the textile industry.

Bulk Pricing
We offer bulk purchasing options, allowing trade customers to save on costs and meet their trade requirements.

Delivery
We offer next day delivery nationwide. Order needed before 12pm to guarantee next day delivery.

Discounts
Exclusive 10% discount on your first purchase by simply subscribing to our newsletter as a new customer.
ï…¤
Complete service
We supply, deliver, install & provide training on all eisenkolb machines. Contact us for details about the puchase process.
0
0
Your Basket
Your basket is emptyReturn to Shop